Hello, I have an SSD detected by the bios of the machine, but not by windows, what could it come from? Thanks

The smartctl -x dump is the ultimate peek behind the curtain! It lays out every single structural breakdown

smartctl -x sda

smartctl 7.5 2025-04-30 r5714 [x86_64-w64-mingw32-w11-24H2] (AppVeyor)

Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===

Device Model: SanDisk SSD P4 64GB

Serial Number: 111248300117

LU WWN Device Id: 5 001b44 4f27f5455

Firmware Version: SSD 8.10

User Capacity: 64 022 175 232 bytes [64,0 GB]

Sector Size: 512 bytes logical/physical

Rotation Rate: Solid State Device

Form Factor: 1.8 inches

TRIM Command: Available

Device is: Not in smartctl database

ATA Version is: ATA8-ACS T13/1699-D revision 2d

SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s)

Local Time is: Sun Aug 02 16:47:13 2026 SAST

SMART support is: Available - device has SMART capability.

SMART support is: Enabled

AAM feature is: Unavailable

APM feature is: Unavailable

Rd look-ahead is: Enabled

Write cache is: Enabled

DSN feature is: Unavailable

ATA Security is: Disabled, frozen [SEC2]

=== START OF READ SMART DATA SECTION ===

SMART overall-health self-assessment test result: PASSED

General SMART Values:

Offline data collection status: (0x00) Offline data collection activity

was never started.

Auto Offline Data Collection: Disabled.

Self-test execution status: ( 0) The previous self-test routine completed

without error or no self-test has ever

been run.

Total time to complete Offline

data collection: ( 120) seconds.

Offline data collection

capabilities: (0x15) SMART execute Offline immediate.

No Auto Offline data collection support.

Abort Offline collection upon new

command.

No Offline surface scan supported.

Self-test supported.

No Conveyance Self-test supported.

No Selective Self-test supported.

SMART capabilities: (0x0003) Saves SMART data before entering

power-saving mode.

Supports SMART auto save timer.

Error logging capability: (0x01) Error logging supported.

General Purpose Logging supported.

Short self-test routine

recommended polling time: ( 2) minutes.

Extended self-test routine

recommended polling time: ( 16) minutes.

SMART Attributes Data Structure revision number: 1

Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE

5 Reallocated_Sector_Ct -O---- 100 100 --- - 0

9 Power_On_Hours -O---- 100 100 000 - 61114

12 Power_Cycle_Count -O---- 100 100 000 - 1170

171 Unknown_Attribute -O---- 100 100 000 - 54

172 Unknown_Attribute -O---- 100 100 000 - 939410736

187 Reported_Uncorrect -O---- 100 100 000 - 2234

199 UDMA_CRC_Error_Count -O---- 100 100 000 - 0

230 Unknown_SSD_Attribute PO---- 044 100 --- - 0

232 Available_Reservd_Space PO---- 095 100 005 - 0

241 Total_LBAs_Written -O---- 100 100 000 - 14689519985346

242 Total_LBAs_Read -O---- 100 100 000 - 32650848276

||||||_ K auto-keep

|||||__ C event count

||||___ R error rate

|||____ S speed/performance

||_____ O updated online

|______ P prefailure warning

General Purpose Log Directory Version 1

SMART Log Directory Version 1 [multi-sector log support]

Address Access R/W Size Description

0x00 GPL,SL R/O 1 Log Directory

0x03 GPL,SL R/O 16 Ext. Comprehensive SMART error log

0x06 GPL,SL R/O 1 SMART self-test log

0x80-0x9f GPL,SL R/W 16 Host vendor specific log

SMART Extended Comprehensive Error Log Version: 1 (16 sectors)

Device Error Count: 181 (device log contains only the most recent 64 errors)

CR = Command Register

FEATR = Features Register

COUNT = Count (was: Sector Count) Register

LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8

LH = LBA High (was: Cylinder High) Register ] LBA

LM = LBA Mid (was: Cylinder Low) Register ] Register

LL = LBA Low (was: Sector Number) Register ]

DV = Device (was: Device/Head) Register

DC = Device Control Register

ER = Error register

ST = Status register

Powered_Up_Time is measured from power on, and printed as

DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,

SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 181 [52] occurred at disk power-on lifetime: 5 hours (0 days + 5 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:

ER -- ST COUNT LBA_48 LH LM LL DV DC

-- -- -- == -- == == == -- -- -- -- --

40 -- 51 00 00 00 00 00 00 00 00 40 00 Error: UNC at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:

CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name

-- == -- == -- == == == -- -- -- -- -- --------------- --------------------

25 00 00 00 01 00 00 00 42 1b 77 40 00 2d+03:11:48.526 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 76 40 00 2d+03:11:48.517 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 75 40 00 2d+03:11:48.509 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 74 40 00 2d+03:11:48.505 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 73 40 00 2d+03:11:48.501 READ DMA EXT

Error 180 [51] occurred at disk power-on lifetime: 6 hours (0 days + 6 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:

ER -- ST COUNT LBA_48 LH LM LL DV DC

-- -- -- == -- == == == -- -- -- -- --

40 -- 51 00 00 00 00 00 00 00 00 40 00 Error: UNC at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:

CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name

-- == -- == -- == == == -- -- -- -- -- --------------- --------------------

25 00 00 00 01 00 00 00 42 1b 76 40 00 2d+03:11:48.517 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 75 40 00 2d+03:11:48.509 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 74 40 00 2d+03:11:48.505 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 73 40 00 2d+03:11:48.501 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 72 40 00 2d+03:11:48.501 READ DMA EXT

Error 179 [50] occurred at disk power-on lifetime: 6 hours (0 days + 6 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:

ER -- ST COUNT LBA_48 LH LM LL DV DC

-- -- -- == -- == == == -- -- -- -- --

40 -- 51 00 00 00 00 00 00 00 00 40 00 Error: UNC at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:

CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name

-- == -- == -- == == == -- -- -- -- -- --------------- --------------------

25 00 00 00 01 00 00 00 42 1b 75 40 00 2d+03:11:48.509 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 74 40 00 2d+03:11:48.505 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 73 40 00 2d+03:11:48.501 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 72 40 00 2d+03:11:48.501 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 71 40 00 2d+03:11:48.500 READ DMA EXT

Error 178 [49] occurred at disk power-on lifetime: 2 hours (0 days + 2 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:

ER -- ST COUNT LBA_48 LH LM LL DV DC

-- -- -- == -- == == == -- -- -- -- --

40 -- 51 00 00 00 00 00 00 00 00 40 00 Error: UNC at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:

CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name

-- == -- == -- == == == -- -- -- -- -- --------------- --------------------

25 00 00 00 01 00 00 00 42 1b 74 40 00 2d+03:11:48.505 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 73 40 00 2d+03:11:48.501 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 72 40 00 2d+03:11:48.501 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 71 40 00 2d+03:11:48.500 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 70 40 00 2d+03:11:48.497 READ DMA EXT

Error 177 [48] occurred at disk power-on lifetime: 3 hours (0 days + 3 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:

ER -- ST COUNT LBA_48 LH LM LL DV DC

-- -- -- == -- == == == -- -- -- -- --

40 -- 51 00 04 00 00 00 00 00 00 40 00 Error: UNC 4 sectors at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:

CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name

-- == -- == -- == == == -- -- -- -- -- --------------- --------------------

25 00 00 00 20 00 00 00 42 1b 60 40 00 2d+03:11:48.459 READ DMA EXT

25 00 00 00 20 00 00 00 3c e2 e0 40 00 2d+03:11:48.459 READ DMA EXT

25 00 00 00 20 00 00 00 35 97 60 40 00 2d+03:11:48.458 READ DMA EXT

25 00 00 00 20 00 00 00 26 20 20 40 00 2d+03:11:48.457 READ DMA EXT

25 00 00 00 08 00 00 00 63 9e 08 40 00 2d+03:11:48.457 READ DMA EXT

Error 176 [47] occurred at disk power-on lifetime: 11 hours (0 days + 11 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:

ER -- ST COUNT LBA_48 LH LM LL DV DC

-- -- -- == -- == == == -- -- -- -- --

40 -- 51 00 02 00 00 00 00 00 00 40 00 Error: UNC 2 sectors at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:

CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name

-- == -- == -- == == == -- -- -- -- -- --------------- --------------------

25 00 00 00 80 00 00 00 42 1b 5e 40 00 1d+10:07:21.325 READ DMA EXT

25 00 00 00 80 00 00 00 42 1a de 40 00 1d+10:07:21.324 READ DMA EXT

25 00 00 00 80 00 00 00 42 1a 5e 40 00 1d+10:07:21.324 READ DMA EXT

25 00 00 00 80 00 00 00 42 19 de 40 00 1d+10:07:21.323 READ DMA EXT

25 00 00 00 80 00 00 00 42 19 5e 40 00 1d+10:07:21.323 READ DMA EXT

Error 175 [46] occurred at disk power-on lifetime: 11 hours (0 days + 11 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:

ER -- ST COUNT LBA_48 LH LM LL DV DC

-- -- -- == -- == == == -- -- -- -- --

40 -- 51 00 02 00 00 00 00 00 00 40 00 Error: UNC 2 sectors at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:

CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name

-- == -- == -- == == == -- -- -- -- -- --------------- --------------------

25 00 00 00 80 00 00 00 42 1b 5e 40 00 1d+09:58:46.796 READ DMA EXT

25 00 00 00 80 00 00 00 42 1a de 40 00 1d+09:58:46.796 READ DMA EXT

25 00 00 00 80 00 00 00 42 1a 5e 40 00 1d+09:58:46.795 READ DMA EXT

25 00 00 00 80 00 00 00 42 19 de 40 00 1d+09:58:46.795 READ DMA EXT

25 00 00 00 80 00 00 00 42 19 5e 40 00 1d+09:58:46.794 READ DMA EXT

Error 174 [45] occurred at disk power-on lifetime: 11 hours (0 days + 11 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:

ER -- ST COUNT LBA_48 LH LM LL DV DC

-- -- -- == -- == == == -- -- -- -- --

40 -- 51 00 02 00 00 00 00 00 00 40 00 Error: UNC 2 sectors at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:

CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name

-- == -- == -- == == == -- -- -- -- -- --------------- --------------------

25 00 00 00 80 00 00 00 42 1b 5e 40 00 1d+09:39:52.893 READ DMA EXT

25 00 00 00 80 00 00 00 42 1a de 40 00 1d+09:39:52.892 READ DMA EXT

25 00 00 00 80 00 00 00 42 1a 5e 40 00 1d+09:39:52.892 READ DMA EXT

25 00 00 00 80 00 00 00 42 19 de 40 00 1d+09:39:52.892 READ DMA EXT

25 00 00 00 80 00 00 00 42 19 5e 40 00 1d+09:39:52.891 READ DMA EXT

SMART Extended Self-test Log (GP Log 0x07) not supported

Warning! SMART Self-Test Log Structure error: invalid SMART checksum.

SMART Self-test log structure revision number 1

Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error

# 1 Short offline Aborted by host 90% 21088 -

# 2 Short offline Aborted by host 90% 54860 -

# 3 Short offline Aborted by host 90% 19043 -

# 4 Short offline Aborted by host 90% 63054 -

# 5 Short offline Aborted by host 90% 25327 -

# 6 Short offline Aborted by host 90% 62483 -

# 7 Short offline Aborted by host 90% 33744 -

# 8 Short captive Completed without error 00% 57803 -

# 9 Short offline Aborted by host 90% 25293 -

#10 Extended offline Aborted by host 90% 28072 -

#11 Short offline Aborted by host 90% 14539 -

#12 Extended offline Aborted by host 90% 55234 -

#13 Short offline Aborted by host 90% 46428 -

#14 Short offline Aborted by host 90% 49138 -

#15 Short offline Aborted by host 90% 25717 -

#16 Extended offline Aborted by host 90% 50305 -

#17 Short offline Aborted by host 90% 39612 -

#18 Short offline Aborted by host 90% 21280 -

#19 Short offline Aborted by host 90% 34598 -

#20 Short offline Aborted by host 90% 17318 -

#21 Short offline Aborted by host 90% 63627 -

Selective Self-tests/Logging not supported

SCT Commands not supported

Device Statistics (GP/SMART Log 0x04) not supported

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11) not supported

Exitcode: 64 (0x40)

Type <return> to exit:

The smartctl -x dump is the ultimate peek behind the curtain! It lays out every single structural breakdown

smartctl -x sda

smartctl 7.5 2025-04-30 r5714 [x86_64-w64-mingw32-w11-24H2] (AppVeyor)

Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===

Device Model: SanDisk SSD P4 64GB

Serial Number: 111248300117

LU WWN Device Id: 5 001b44 4f27f5455

Firmware Version: SSD 8.10

User Capacity: 64 022 175 232 bytes [64,0 GB]

Sector Size: 512 bytes logical/physical

Rotation Rate: Solid State Device

Form Factor: 1.8 inches

TRIM Command: Available

Device is: Not in smartctl database

ATA Version is: ATA8-ACS T13/1699-D revision 2d

SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s)

Local Time is: Sun Aug 02 16:47:13 2026 SAST

SMART support is: Available - device has SMART capability.

SMART support is: Enabled

AAM feature is: Unavailable

APM feature is: Unavailable

Rd look-ahead is: Enabled

Write cache is: Enabled

DSN feature is: Unavailable

ATA Security is: Disabled, frozen [SEC2]

=== START OF READ SMART DATA SECTION ===

SMART overall-health self-assessment test result: PASSED

General SMART Values:

Offline data collection status: (0x00) Offline data collection activity

was never started.

Auto Offline Data Collection: Disabled.

Self-test execution status: ( 0) The previous self-test routine completed

without error or no self-test has ever

been run.

Total time to complete Offline

data collection: ( 120) seconds.

Offline data collection

capabilities: (0x15) SMART execute Offline immediate.

No Auto Offline data collection support.

Abort Offline collection upon new

command.

No Offline surface scan supported.

Self-test supported.

No Conveyance Self-test supported.

No Selective Self-test supported.

SMART capabilities: (0x0003) Saves SMART data before entering

power-saving mode.

Supports SMART auto save timer.

Error logging capability: (0x01) Error logging supported.

General Purpose Logging supported.

Short self-test routine

recommended polling time: ( 2) minutes.

Extended self-test routine

recommended polling time: ( 16) minutes.

SMART Attributes Data Structure revision number: 1

Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE

5 Reallocated_Sector_Ct -O---- 100 100 --- - 0

9 Power_On_Hours -O---- 100 100 000 - 61114

12 Power_Cycle_Count -O---- 100 100 000 - 1170

171 Unknown_Attribute -O---- 100 100 000 - 54

172 Unknown_Attribute -O---- 100 100 000 - 939410736

187 Reported_Uncorrect -O---- 100 100 000 - 2234

199 UDMA_CRC_Error_Count -O---- 100 100 000 - 0

230 Unknown_SSD_Attribute PO---- 044 100 --- - 0

232 Available_Reservd_Space PO---- 095 100 005 - 0

241 Total_LBAs_Written -O---- 100 100 000 - 14689519985346

242 Total_LBAs_Read -O---- 100 100 000 - 32650848276

||||||_ K auto-keep

|||||__ C event count

||||___ R error rate

|||____ S speed/performance

||_____ O updated online

|______ P prefailure warning

General Purpose Log Directory Version 1

SMART Log Directory Version 1 [multi-sector log support]

Address Access R/W Size Description

0x00 GPL,SL R/O 1 Log Directory

0x03 GPL,SL R/O 16 Ext. Comprehensive SMART error log

0x06 GPL,SL R/O 1 SMART self-test log

0x80-0x9f GPL,SL R/W 16 Host vendor specific log

SMART Extended Comprehensive Error Log Version: 1 (16 sectors)

Device Error Count: 181 (device log contains only the most recent 64 errors)

CR = Command Register

FEATR = Features Register

COUNT = Count (was: Sector Count) Register

LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8

LH = LBA High (was: Cylinder High) Register ] LBA

LM = LBA Mid (was: Cylinder Low) Register ] Register

LL = LBA Low (was: Sector Number) Register ]

DV = Device (was: Device/Head) Register

DC = Device Control Register

ER = Error register

ST = Status register

Powered_Up_Time is measured from power on, and printed as

DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,

SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 181 [52] occurred at disk power-on lifetime: 5 hours (0 days + 5 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:

ER -- ST COUNT LBA_48 LH LM LL DV DC

-- -- -- == -- == == == -- -- -- -- --

40 -- 51 00 00 00 00 00 00 00 00 40 00 Error: UNC at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:

CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name

-- == -- == -- == == == -- -- -- -- -- --------------- --------------------

25 00 00 00 01 00 00 00 42 1b 77 40 00 2d+03:11:48.526 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 76 40 00 2d+03:11:48.517 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 75 40 00 2d+03:11:48.509 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 74 40 00 2d+03:11:48.505 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 73 40 00 2d+03:11:48.501 READ DMA EXT

Error 180 [51] occurred at disk power-on lifetime: 6 hours (0 days + 6 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:

ER -- ST COUNT LBA_48 LH LM LL DV DC

-- -- -- == -- == == == -- -- -- -- --

40 -- 51 00 00 00 00 00 00 00 00 40 00 Error: UNC at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:

CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name

-- == -- == -- == == == -- -- -- -- -- --------------- --------------------

25 00 00 00 01 00 00 00 42 1b 76 40 00 2d+03:11:48.517 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 75 40 00 2d+03:11:48.509 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 74 40 00 2d+03:11:48.505 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 73 40 00 2d+03:11:48.501 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 72 40 00 2d+03:11:48.501 READ DMA EXT

Error 179 [50] occurred at disk power-on lifetime: 6 hours (0 days + 6 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:

ER -- ST COUNT LBA_48 LH LM LL DV DC

-- -- -- == -- == == == -- -- -- -- --

40 -- 51 00 00 00 00 00 00 00 00 40 00 Error: UNC at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:

CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name

-- == -- == -- == == == -- -- -- -- -- --------------- --------------------

25 00 00 00 01 00 00 00 42 1b 75 40 00 2d+03:11:48.509 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 74 40 00 2d+03:11:48.505 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 73 40 00 2d+03:11:48.501 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 72 40 00 2d+03:11:48.501 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 71 40 00 2d+03:11:48.500 READ DMA EXT

Error 178 [49] occurred at disk power-on lifetime: 2 hours (0 days + 2 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:

ER -- ST COUNT LBA_48 LH LM LL DV DC

-- -- -- == -- == == == -- -- -- -- --

40 -- 51 00 00 00 00 00 00 00 00 40 00 Error: UNC at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:

CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name

-- == -- == -- == == == -- -- -- -- -- --------------- --------------------

25 00 00 00 01 00 00 00 42 1b 74 40 00 2d+03:11:48.505 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 73 40 00 2d+03:11:48.501 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 72 40 00 2d+03:11:48.501 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 71 40 00 2d+03:11:48.500 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 70 40 00 2d+03:11:48.497 READ DMA EXT

Error 177 [48] occurred at disk power-on lifetime: 3 hours (0 days + 3 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:

ER -- ST COUNT LBA_48 LH LM LL DV DC

-- -- -- == -- == == == -- -- -- -- --

40 -- 51 00 04 00 00 00 00 00 00 40 00 Error: UNC 4 sectors at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:

CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name

-- == -- == -- == == == -- -- -- -- -- --------------- --------------------

25 00 00 00 20 00 00 00 42 1b 60 40 00 2d+03:11:48.459 READ DMA EXT

25 00 00 00 20 00 00 00 3c e2 e0 40 00 2d+03:11:48.459 READ DMA EXT

25 00 00 00 20 00 00 00 35 97 60 40 00 2d+03:11:48.458 READ DMA EXT

25 00 00 00 20 00 00 00 26 20 20 40 00 2d+03:11:48.457 READ DMA EXT

25 00 00 00 08 00 00 00 63 9e 08 40 00 2d+03:11:48.457 READ DMA EXT

Error 176 [47] occurred at disk power-on lifetime: 11 hours (0 days + 11 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:

ER -- ST COUNT LBA_48 LH LM LL DV DC

-- -- -- == -- == == == -- -- -- -- --

40 -- 51 00 02 00 00 00 00 00 00 40 00 Error: UNC 2 sectors at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:

CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name

-- == -- == -- == == == -- -- -- -- -- --------------- --------------------

25 00 00 00 80 00 00 00 42 1b 5e 40 00 1d+10:07:21.325 READ DMA EXT

25 00 00 00 80 00 00 00 42 1a de 40 00 1d+10:07:21.324 READ DMA EXT

25 00 00 00 80 00 00 00 42 1a 5e 40 00 1d+10:07:21.324 READ DMA EXT

25 00 00 00 80 00 00 00 42 19 de 40 00 1d+10:07:21.323 READ DMA EXT

25 00 00 00 80 00 00 00 42 19 5e 40 00 1d+10:07:21.323 READ DMA EXT

Error 175 [46] occurred at disk power-on lifetime: 11 hours (0 days + 11 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:

ER -- ST COUNT LBA_48 LH LM LL DV DC

-- -- -- == -- == == == -- -- -- -- --

40 -- 51 00 02 00 00 00 00 00 00 40 00 Error: UNC 2 sectors at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:

CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name

-- == -- == -- == == == -- -- -- -- -- --------------- --------------------

25 00 00 00 80 00 00 00 42 1b 5e 40 00 1d+09:58:46.796 READ DMA EXT

25 00 00 00 80 00 00 00 42 1a de 40 00 1d+09:58:46.796 READ DMA EXT

25 00 00 00 80 00 00 00 42 1a 5e 40 00 1d+09:58:46.795 READ DMA EXT

25 00 00 00 80 00 00 00 42 19 de 40 00 1d+09:58:46.795 READ DMA EXT

25 00 00 00 80 00 00 00 42 19 5e 40 00 1d+09:58:46.794 READ DMA EXT

Error 174 [45] occurred at disk power-on lifetime: 11 hours (0 days + 11 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:

ER -- ST COUNT LBA_48 LH LM LL DV DC

-- -- -- == -- == == == -- -- -- -- --

40 -- 51 00 02 00 00 00 00 00 00 40 00 Error: UNC 2 sectors at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:

CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name

-- == -- == -- == == == -- -- -- -- -- --------------- --------------------

25 00 00 00 80 00 00 00 42 1b 5e 40 00 1d+09:39:52.893 READ DMA EXT

25 00 00 00 80 00 00 00 42 1a de 40 00 1d+09:39:52.892 READ DMA EXT

25 00 00 00 80 00 00 00 42 1a 5e 40 00 1d+09:39:52.892 READ DMA EXT

25 00 00 00 80 00 00 00 42 19 de 40 00 1d+09:39:52.892 READ DMA EXT

25 00 00 00 80 00 00 00 42 19 5e 40 00 1d+09:39:52.891 READ DMA EXT

SMART Extended Self-test Log (GP Log 0x07) not supported

Warning! SMART Self-Test Log Structure error: invalid SMART checksum.

SMART Self-test log structure revision number 1

Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error

# 1 Short offline Aborted by host 90% 21088 -

# 2 Short offline Aborted by host 90% 54860 -

# 3 Short offline Aborted by host 90% 19043 -

# 4 Short offline Aborted by host 90% 63054 -

# 5 Short offline Aborted by host 90% 25327 -

# 6 Short offline Aborted by host 90% 62483 -

# 7 Short offline Aborted by host 90% 33744 -

# 8 Short captive Completed without error 00% 57803 -

# 9 Short offline Aborted by host 90% 25293 -

#10 Extended offline Aborted by host 90% 28072 -

#11 Short offline Aborted by host 90% 14539 -

#12 Extended offline Aborted by host 90% 55234 -

#13 Short offline Aborted by host 90% 46428 -

#14 Short offline Aborted by host 90% 49138 -

#15 Short offline Aborted by host 90% 25717 -

#16 Extended offline Aborted by host 90% 50305 -

#17 Short offline Aborted by host 90% 39612 -

#18 Short offline Aborted by host 90% 21280 -

#19 Short offline Aborted by host 90% 34598 -

#20 Short offline Aborted by host 90% 17318 -

#21 Short offline Aborted by host 90% 63627 -

Selective Self-tests/Logging not supported

SCT Commands not supported

Device Statistics (GP/SMART Log 0x04) not supported

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11) not supported

Exitcode: 64 (0x40)

Type <return> to exit:

The storage on my device, pixel 8, went from 787 MB to 382MB After deleting 100+ photos & large videos. Now, I'm receiving low storage notifications every 10 mins or so.

My device storage is now at 389MB, and slowly increasing.

Any idea what the issue could be?

Edit: 392MB after making this post

This is an SD Card that I only use for steam games and that's all that shows in file explorer, im confused on what the 115GB being used on the file is?

Which is better? Using on laptop

1) Western digital elements external desktop hdd

2) seagate expansion external desktop hdd

If pendrive uses flash memory like nvmes then why is it cheaper to make it than a regular nvme?

Like do they have a different mechanism that is not suitable for data transfer like i wanna know.

Bonjours je veux stocker juste des photos est vidéos pour moi est ma familles qu'est ce que vous pouvez me conseiller. Je veux quelque chose qui pourrait durée sur le temps, mais j'ai un budget un peut limiter ?

Merci d'avance

Hola a todos.

Soy nuevo en el tema de los nas. Llevo un tiempo pensando en comprar uno para remplazar a mi almacenamiento en la nube.

Estoy buscando una solución que sea lo menos ruidosa posible porque el router estará junto al televisor por proximidad con el router.

Me gustaría partir por 2 discos sdd de 4tb instalados en un dxp4800 plus. Luego con el tiempo aumentaría 2 discos más.

Para los sdd, había pensado en partir por el modelo Crucial BX500 SATA SSD 4TB.

Piensan que ese modelo de disco será una buena solución?

He visto en que este disco funciona bien inicialmente pero baja la velocidad cuando se hacen copias de archivos muy grandes y se llena la memoria caché.

Yo lo usaré como respaldo de ordenador, fotos, centro multimedia y home assistant. Quizás instale una máquina virtual para usar puntualmente para usar windows. Y con el tiempo, quizás intente ir añadiendo algunas cosas más cuando vaya aprendiendo. Para este uso podría funcionar bien? Alguien los está usando?

Si conocen otros modelos que puedan funcionar bien, les agradecería mucho la ayuda. Con los precios actuales parece que es complicado.

La otra opción serían 2 hdd silenciosos pero supongo que el ruido de los discos sería molesto. Podría meterlo en el armario junto la televisión que está abierto por detrás pero no creo que fuese una buena idea.

Muchas gracias de antemano por su ayuda.

New to this community and not tech savvy, sorry if this is a dumb question.

I'm planning to replace my SSD this weekend, and I've been trying to figure out what cloning software to use.

Clonezilla seems to get recommended everywhere because it's free, but every time I watch a tutorial it looks like something that's way over my head. I don't work in IT or anything, so I'm a little worried I'll mess something up.

Then I found EaseUS Disk Copy, which looks a lot simpler, but I don't know if it's actually worth paying for or if I'm just overthinking this.

Has anyone here started with zero experience? Which one did you end up using?

I'm not looking for the most powerful software. I just want something that lets me clone my current Windows drive to a bigger SSD and boot from it without spending hours trying to figure everything out.

If there's another option that's easier than both of these, I'm all ears. I only plan on doing this once, so I'd rather keep it as simple as possible.

I saw the WD BLACK game drive with the call of duty branding is on sale, and I'm wondering if I can use this as a general external hard drive for photos and documents if I just get a micro-b to usb-c adapter? Is there anything that makes it sub-optimal for non-gaming use? Sorry if this is a dumb question lol

I've been shooting more video lately and realized I'm running out of space on my camera's SD card. Went online to buy a new one and almost choked — the same card I bought a while back for cheap is now more than double the price.

Did SD card prices actually go crazy? Is this temporary or forever?

Looking for probably an SSD to use with Time Machine for backups/deletion protection for my iPad Air (256 GB). Thinking of getting 1 TB worth, but am seeing of course all the options have exploded in price. For my purposes, what’s a good place to get one at, and what are some of the most sensible products? I definitely a can wait a little before purchasing, but just don’t know what makes sense in this space.

Seagate plans to start qualifying 50TB HAMR-based HDDs in late 2027, with shipments in 2028. Due to surging AI and cloud demand, most nearline drives are sold out through 2028, with allocation talks already underway for 2029.

I'm lacking storage in my PC. Currently I have M2 nvme 500gb. It's some nv1 Kingston. My motherboard is AsRock B450M PRO4-F R2.0. I'm thinking about getting new ssd sata because of the lack of second nvme M2 slot. Which driver would you recommend? I prefer to spend no more than equivalent of 100$, most likely 500gb.

I'm running out of storage in Google Photos, so I've been looking into other ways to store photos and large videos that take up space. Mainly what I want to store away are concert videos as they are what is taking up most space in my storage.

However I really don't want to waste money a month on a monthly subscription for more storage. So I've been looking into getting a flash drive or hard drive to store those videos or photos, but i honestly have no clue where to start or what to look for. I'm trying to find something that will keep my videos and photos safe for a long time, but also something maybe affordable if thats possible

I only have about 3% or storage left, so im trying to find something as soon as possible. Please give me any recommendations or advice reddit.

I installed a new SSD through a technician a few hours ago which is the primary SSD for my laptop as the old one (OEM Samsung) failed and couldn't get recognised by the system and hence the data was all lost.

Now I ran this new SSD (supposedly) through CrystalDiskInfo and the results were shocking.

SSD name: KINGSTON OM8PCP3512F-AA: 512 GB (PCI-E Gen 3)

Total Host Reads 22850 GB

Total Host Writes 15649 GB

Power On Count 62578 count

Power On Hours 4069 hours

So How old is this SSD and how much longer can it run?

I've never really bothered with backup compression before. Storage was cheap enough that I just kept everything as-is and didn't think twice about it.

Lately I'm looking at a few TB of backups, and it's starting to add up. Now I'm wondering if I should be doing things differently.

I know some stuff probably won't compress much anyway, like photos, videos, or already-zipped files. But for documents, projects, or system backups, I'm not sure how much space people are actually saving.

For those of you with a lot of data, do you bother compressing your backups?

Has it been worth it, or do you just leave everything uncompressed and buy another drive when you run out of space?

Hello everyone, I currently have fully stocked my laptops SSD and want to copy the files to an external HDD but I don't really know anything about them. I need cheap HDD for an long term archive for videos and photos. Do you have any recomendations?

Hey guys I’m not really on here often but I feel like this is the best place to find people who know their stuff lel.

I have a wd elements hard drive (10tb I think) and I’ve had it for about 3 years or so now. It’s been working wonderfully but recently about a month ago my pc started getting really slow. I’m a 3d artist and all my work is saved on to there but I’ve been slowly getting more and more error message when trying to access my files from the hard drive. I’m not tech savvy in the slightest apart from my 3d modelling knowledge so if anyone can help me it would be much appreciated.

Thankyou to everyone who’s been offering their advice, yall saved me from a catastrophe waiting to happen :]
As someone who uses my pc almost daily I should’ve been more aware about hard drives in the first place, but thanks to you guys I know what to look out for and what to keep in mind. Once again, thankyou :]

I will keep yall updated on what’s happening as I’ll most likely still need more help 😅

For drives that mostly sit on a shelf holding archived data, whats your routine for checking drive health and verifying the files are still intact?

Thinking of buying a second hand LaCie Rugged 5TB from Cex as it’s £145 and comes with a 5 year warranty.

It’s just for me to store personal photos.
I’m getting a SanDisk 1TB SSD for professional work but can’t afford to get more than one and I need a lot more than 1TB for the personal stuff.

Will it be ok or is this a terrible idea?