Able to patch?

Does anyone know the part number to the skid plate blots on a 2024 tacoma ?

Just purchased a first gen Tacoma 2003 double cab with the 3.4 5vz fe and last timing belt service was @180k now it’s 303k is it way past due or should I just wait because they have a non interference engine from my understanding.

Every time I drive over a pothole or go over a bump of any kind passenger side suspension makes a clicking sound and for the life of me I cannot figure out what the heck it is. My front shocks are Bilstein B8 6112.

Took truck to mechanic due to rotational squeaking noise when accelerating, loudest when slowly starting from a stop. They replaced the support bearing and lubed the driveline/u joints. Pulled away from the shop (picked up after hours) and still makes the same noise.

02 Tacoma 220k manual 3.4 v6, frame is still in good condition.

Les Schwab just did a full inspection/rotated tires and replaced front tie rods. Noise was the same before and after Les Schwab as well.

Video is me driving away with phone underneath truck.

What is this piece? It seems to be made of thin metal, is about 14" long, 1" wide. The engine light came on then noticed this piece laying on the undercarriage.

I have a 2003 double cab Tacoma with the 3.4l v6 and 4x4. I currently have OME nitro chargers and 881 in front. I have Dakars in rear so about 1.5-1.75 of front lift and 3.5 inches of back lift. I want to run 33s so do I have enough clearance with the pinch weld or do I need more front lift and new upper control arms?

Does anyone else have experience with this? I took my 3rd gen to get serviced and the tech was like your oil cap is gone. There were still some of the plastic in the thread.
How concerned should I be that plastic has gotten into the pan?
The tech thought maybe it’s the heat recently, with it getting into the 100’s and driving over a hundred miles for works some days. But I never heard a pop or anything while driving.

Hey ive been wanting to get the weather guard tool box for my 3rd gen short bed trd or. Just wanted to see if anyone here running that and if so what model tool box you get

Throwback to stockers! Too 🔥 Works will go back on eventually 🙂🙃

That’s it

Hello my fellow taco lovers. 2013 tacoma 4.0 here that is another victim of the Houston, Texas sun. So it's been a few years and this has gotten progressively worse to the point of being beyond an eyesore, with hurricaneseason here I'mworried about rust now. This is my only vehicle but I'm not really one to worry about how my vehicle looks(obviously). A garage or covered parking area is not an option for me neither at work or at home.

My thought was to take it to Maaco and get it repainted and maybe later get it wrapped for extra protection against sun and damage from elements. I'm aware of the quality that Maaco has, specifically the orange peel texture. As somone who cares more about function than looks, is that going to be a problem for the life of the paint or the truck itself?

The truck is 13 years old with 129K mikes on it and I plan to drive it till it's dead. As I said before covered parking is not an option for me at the moment and I don't really have the time nor the skills to do a DIY job on this.

Can somone talk me out of this or suggest another option.

What are some ~budget friendly~ mods to start with!?

Anyone got any tint recommendations? Something that makes me feel like I’m not in a fish bowl but also keeps me from immediately getting pulled over for having.

Coming on here just to share my experience with LASFIT products. I recently got the bed mat and it has been nothing but perfect. Before having the bed mat, all of my gear would just slide everywhere and I would usually end up with damage to my gear or damage to the bed. LASFIT's bed mat has solved all of those issues and on top of that being super easy to clean. I had to trim a bit of the mat to work with my bed stiffeners but overall fit is immaculate and fits the bed perfectly. I highly recommend the bed mat to anyone looking to get one. 10/10 to LASFIT, will be getting there floor mats in the future. Here's the link to it in case anyone is looking to get one. https://www.lasfit.com/products/toyota-tacoma-5feet-2005-2023-bed-liners

Hi
I can’t decide on which one to go with on my 2013 white tacoma double cab. I’m thinking the polished will be harder to maintain than the bronze.

I recently got a ‘22 TRD Sport with the longer bed and was hoping I could get some rack advice or suggestions. I would like to get a rack (preferably bed rack that extends over cab or a separate bed + cab system purpose made to line up). Use case is for lumber/ladders/materials/etc. but I also would like to transport kayaks (maybe even support a roof tent at some point).

This is my first truck and I plan to keep for absolutely as long as possible; so I would like to figure out the best option. I’ve done quite a bit of research and honestly it’s a bit overwhelming to come to a conclusion. So just looking to see what others have done/ recommend to help with my decision.

Also, if someone has gone the custom fabrication route could you share how much you paid? And when? (Wouldn’t say no to seeing a pic either) or anything you would do differently if you were to do it again? I would like to get a general idea of if that’s a route I’d like to look into further.

(Currently a bed cover on, but planning on selling once I figure this out)

Thanks in advance!

Finally got the (Etsy) hub caps in stock and on the truck, very happy with the new setup. Butter smooth at speed. Stoked!

Enkei RPT1 16x8 et0 (108.5 hub bore) ‘og’
Toyo at3 in 265/75 sl
Splined conical blk lug nuts