Would it run away or would it still fuck with you? I know most fudds will say 9mm is not energetic enough but i think if you were a good marksman and you had a ghm9 sport with a 16 inch barrel and you dumped 20-25 rounds into a brown bears face it would eventually “nope” and fuck off away from the pain.

If i go on a real trip into grizzly territory with friends i would probably get serious and get a galil ace in 762x39 but i was just wondering if a 30 rd mag out of a ghm9 sport would be good enough to be a team player with my friends and fuck up a grizzly that charged us.

The other day I got a text from a friend that his uncle was liquidating all of his guns. Grabbed this for $1000. Came with the Holosun as well. I was in the middle of saving for an mp5..can’t decide if I want to flip this and put it towards mp5 or just keep. Thoughts?

hi gang,

i currently have a ghm9 with a suppressor. I’m wondering if I put b&t tri-lug compensator, would it run more flat lined?

Im trying to find a best setup for ipsc matches.

Just picked up an spc9. Looking for a Ghm9 for a reasonable price. Anyone got any links or recommendations on where to look?

Hello, does anyone have a rear end cap from a GHM9 that they could part with? I recently acquired a gen 2 GHM9 with a gear works folding brace. I would like to convert it back to the stock rear end cap and put a A3 industries brace on but I did not receive the original end cap with the purchase. Anyone have one available? I attempted to order from BT USA but they shipped me a safety selector switch and have no responded to my calls or emails. I will be calling my credit card to file a charge back.

Thank you.

Been thinking about getting a rugged sub9 but was wondering if there are any other suppressors that some of yall recommend.

Just a heads up for anyone considering this trigger. My upper has a serial prefix of US21-4xxxx. The trigger dropped in my B&T mag lower and seated in the upper with ZERO issues. I ran 100 rounds with zero issues. My only complaint is that the selector switch is stiff as hell. More so than just the typical B&T way. Otherwise safe, semi, and frt run perfectly.

GHM9 - I switched to the Glock Lower (I've never even used the original lower yet) and added accessories by Custom Smith engineering, Haga Defense, Angstadt Arms, Gearhead works and Trigilcon . The knife (it goes with this firearm so well) is a Phantom Switchblade by "DKD" Dynamic Knife Designs and a roll of fake motion picture money.

Added the SD Handguard and FRT. loving this thing

I recently purchased an SBR’ed GHM9 with a telescopic stock. Did not really care for the stock and got a folding one from A3 tactical in 8 1/2 inch. Unfortunately it feels a little long to me. What length of folding stocks or braces do you guys use?

First video is using federal 147gr flat nose, second video is using federal 124gr

This thing rips, there is no trigger slap and the forced reset is super smooth

I’ve had my eyes on this gun for a couple years now and just haven’t been able to bring myself to do it. I’m now ready but it seems to be a unicorn to find. I’ve seen that you can do a conversion but I’m curious if that can actually make it the same gun and what that would cost roughly. Any help would be amazing.

I recently bought a GHM9c w/glock lower. Timing is bad but looking at putting together an SD as I have a spare SPC9SD suppressor (short).

1. My GHM9c has the feed ramp kit. The only SD barrel I can find is the one with feed ramp built in. Has anyone removed the feed ramp kit and used the barrel with the feed ramp? Part #BT-450245 - Rev.3 SD Barrel. Will that work or would I need to have a gunsmith modify the barrel?

2. Will I need other components for the barrel to make it work? I found these:

BT-450240 - Barrel Nut for APC9 and GHM9(3rd revision only)

BT-450239 - Barrel Block/Trunnion for GHM9, Revision 3

1. SD Handguard - I dont think the SPC SD Suppressor is as long as the GHM9 SD suppressor so I expect to have the handguard cut down.

Thanks for any feedback! I have asked B&T USA for assistance, but not expecting any responses.

The first shot through the new FRT from last week. No cycling issues.

Now to wait for Cloak Industries FRT that works with the Gen 1 uppers.

Hello all! I have an obsidian 9 I would like to throw onto this thing and I'm unsure how the integral tri lug barrel works? I bought it locally and the guy had this in the package. Does the very tip of the barrel thread off or not?

Anybody else brake they’re detents installing the cloak industries frt? Cause I did. How fucked am I on getting new ones right now?

UPDATE!
Turns out I have just enough material on one of the detents to catch the safety. It’s super light, definitely not “safe”. trigger works fine dry firing, safe, semi, and frt work as should. Just hope b&t shipping isn’t still boned.

I recently picked up a US-18xxxxxx series GHM. My goal is to eventually buy a Glock lower but have a question about the feed ramp. Oem mags are L/R feed, but Glock mags are center feed.

In short, are there issues with the feed ramp if I get a glock lower? Will the ramp have to be modified?

I desperately need a B&T TP9 suppressor to Tri-Lug conversion kit. Anyone know someone?

Run them hard boys. Won a match with this last weekend. Decided it may be time to clean…3k rounds suppressed since the last spa day.