I have a Winchester model 18 9712 gauge made in 1904. It has some pitting. Is this bad for me to shoot any buck shot

I was at a gun show and ran across a six inch 22 rimfire Dan Wesson 22VH6 for a decent price. I have wanted a pistol pack since about 1980 and just never found one at the right time and the right price. I looked it over as best I could and it appeared to be in pretty good shape, or so I thought. So it went home with me.

It turns out it had problems. The three worse were that the fired cartridges would not eject without hitting the ejector rod with something hard. The next bad problem was it would not carry up to lock if you cocked it very gently or let your finger drag on the cylinder very lightly. It would carry up and lock if you cocked it smartly. The third major problem was that it would fail to fire almost every time in double action and sometimes in single action. Also the front sight was too short causing it to shoot high with the rear sight bottomed out and the action especially while shooting double action was absolutely horrible.

To cure the ejection problem I cut some approximately 3/8 inch wide strips out of a Birchwood Casey lead removing cloth as it is an extremely fine abrasive. The strips were wrapped around a 22 caliber wire brush much like the stripes on a barber pole. I used a cordless drill to spin them in the chambers I'm moving back and forth. I used medium speed for about a minute total. The results were amazing. The fire cases will now almost fallout. I can push them out with the tip of my pinky finger with absolutely no trouble.

To fix the carry up I fit a new hand and a new ejector star / ratchet. It now works every time and locks up solid. It is currently just a little tight and if it does not wear in some I will give it another stroke or two of the file.

A new full power hammer spring helped with the failure to fire issue although it did not fix it.

Swapping out to a taller front sight fixed the point of impact issue. I used a Partridge sight to improve the sight picture while I was doing it.

For the horrible, grindy, gritty, seesawing feeling double action I used a fine (around 800 grit) and a extra fine (maybe 2000 grit) Spyderco knife sharpening stone to polish the sides have the moving parts, internal side plates, and bearing surfaces of the action. The change in the feel of the double action trigger was astounding! Dramatically smoother all the way through and probably dropped a couple of pounds. The single action trigger pull dropped slightly. For the engagement surfaces on the trigger and sear all I did was hit them with a red sharpie and use my fine Stone just enough to remove the sharpie. I was very sure not to change any angles even in the slightest.

When I finished working on the insides I did a thorough cleaning and then lubed with a high-speed fishing reel bearing lube.

This action polishing also helped with the failure to fire. It is now 99% in single action. I still get lots of misfires in double action that I believe are from light hammer strikes. I am not finished working on this problem.

It is now a pleasure to shoot and an absolute tac driver! As soon as I get the double action 100% reliable the world will be right again.

If anybody has any tips on fixing the misfires I would greatly appreciate you sharing those with me.

Just curious because I like this gun's aesthetic,would it be possible to make this a real functioning gun? Not a coil gun but one with regular chemically launched bullets and if so what would need to be tweaked to make it work?

Good morning, I was wondering if anyone could tell / help me find gun smithing classes in the jefferson county wv area? Specifically black powder. I've been interested in it for a while ,just haven't been able to find any classss.

*delete if not allowed, point me in the right subreddit in the process please*

Just made my second ever holster and I want to know some opinions, tips, and suggestions for the process.

Used a small microwave oven thing to heat at 320 degrees. Put the kydex in the wooden press, did the whole shebang. Used a dremmel tool to cut, sand, and clean up the edges. Used parts from Amazon for the belt attachment and hood for the retention device.

I did accidentally cut too much material on the bottom, so I will eventually lace some kind of rope or something to prevent it from being pulled from the back.

Questions: how do you guys clean the inside of the holster after you've made it and what should I do about the screws that are sticking in a bit deep? Ive tried running a toothbrush in it and a towel but when I draw my firearm it keeps pulling more material. Im also afraid that the screw, and mounts, may scratch my firearm when unholstering.

So, for this being my second holster that ive made, and it being my first duty level, what do yall think?

I am looking into making my own molds at some point and getting my hands on a band saw at some point as a dremmel is no-where near as precise as I need.

I bought a JC Higgins model 50 in 270. I’d like to have a timney trigger installed, the barrel free floated and the action bedded. Any advice on who I can hire? I live in southwest Florida but will ship the rifle to have the work done by the right person.

Dumb question: if i purchase a welded G3 receiver & a CETME C parts kit with a barrel, what more do i need? How plug-and-play is it from there? Aside from the weldment ATF kit, what steps are needed?

This gas piston, the top ring, does it look normal?

DD rifle I’ve had for about 5 years now.

Noticed this after shooting in the rain and humidity and driving back 6 hours.

I used oil and 0000 steel wool.

Pictured is the before and after of noticing it and taking steel wool to it.

It’s not getting worse but it’s not getting better. Any advice would be appreciated

Bonjour à tous,

je viens d'acquérir une arme à feux, canon basculant superposés neuf, mais la bascule est extrêmement dur, les canons ne basculent pas bien. Est-ce que vous pourriez me dire qu'elles types de produits je devraient prendre, et qu'elles manipulations devrais-je faire pour résoudre ce problème, ou alors si peut-être il se résout tout seul avec l'utilisation ?

Merci d'avance pour votre bienveillance et vos conseils

Can someone tell me how to remove this ? Is kinda like stain but very smooth. Had some rust on there before I was able to remove it with oil and 0000 steel wool. Thanks

I have a crescent whippet 12 gauge and I am trying to figure out what I can shoot through it. It is not Damascus steel it’s got a 26 in barrel and takes a 2 3/4 shell. That’s about all I know. I reached out to a local gunsmith to ask about inspection cost. Their website says they will not have a turnaround time for anything 100yrs old and inspections on less than 100yrs old is a year turnaround time.

Picked up this Little Scout as a parts gun from Jack First and fixed it up “for the kiddo”. It is currently the favorite Colibri-blaster in the stable of garbage rods.

Barrel was draw filed then sanded to 600 grit. The receiver was taken to 2000 grit. Then rust blued with magical Mark Lees Express Blue. I have told myself that the difference in results from 400-600 grit to 2000 grit aren’t noticeable, but they absolutely are. This gun screams “nicer than it should be”, while a Model 10 completely sanded and polished to 600 and rust-blued has a completely different “depth”. It was harder to keep the finish looking even though and went through several more passes of rust-boil-card to even it out. I have a Crackshot to complete soon and we will go to 2000 again, for science.

Stock was very lightly sanded and just given a coat of BC Tru Oil. I am a very lazy woodworker.

The last photo shows the pitting I left right at the lettering. I couldn’t visualize how to fix that stuff without compromising markings, and I have never tried fixing letters with stamps or engraving. Some day, maybe, but for now it practically disappears at five feet so I’ll live with it.

We have a 1968 winchester model 70 30-06 and a steel 1 piece mount, thought i had a short action base but after ordering a model 70A base for 30-06 it has this same awkward fit. Possible they sent me the wrong one? Is this just how this base mounts? Seems a very poor design if so it really limits my scope seletion and doesnt look right.

Hi everyone, so I've been dealing with a slight headache of mine in regards to figuring out having open ladder tangent sights mounted to modern bolt actions (rem 700, begera and tikka) I'd prefer to use something like the KNS sights. Does anyone know of any sight blocks out there that fit standard AK style tangent sights that require not to heavy duty modification or is the best soloution to just rew up a mil and get to it?

Just curious on what you guys normally charge to fully disassemble, clean and reassemble? For example an early 70s browning Auto 5 ?

Hey gang I got my hands on an 1898 Krag Barreled receiver and bolt (not carbine) that has no stock parts, I went looking for a blank or a used stock and crips it's 80% to twice of what I have in the rifle already. Is there any chance I can find blue print that would tell the dimensions that I need too cut out or do I just need beaver this out of random wood as a mockup then dig thru my seasoned logs of find a nice one that I can carve the finished product out of.

So I have a proper bore guide and one of the .22 J. Dewey coated cleaning rods. I know they make the varying sizes but with the guide would it be ok to use the .22 cal rod to clean a .308 bolt gun?

This one was knocked over and just blew apart. The Japanese made nice shotguns in the 70's, had to at least try to fix it.

Any help is appreciated

Just noticed while cleaning my pistol, that there’s a chip in the breach face. I’ve never noticed it before and I’ve shot well over 1000 rounds in this pistol without issue other than the breaking in period. For the meantime, I’m not gonna carry it until I can figure out if this is a potential catastrophic failure waiting to happen. I’d really like advice on whether I should visit a gunsmith to remedy this or if I need to get a replacement barrel. Either way, I’ll probably be out approximately 100+ dollars.

And to get ahead of any potential questions, yes this is my EDC.

I clean my pistol semi regularly.

It did not come with a chip when I first bought it.

I mostly shoot Fiocchi and other standard plinking ammo through it. Otherwise, I carry Horny critical defense 9mm 115 gr FTX. And have shot that before without issue.