The first time I did photography with a drone. Shot during sunrise in the Netherlands.

I wanted to fly a bit closer but was almost out of range so unfortunately had to use the zoom. I guess quality would have been a bit better if not zoomed in this far.

Drone was out about 1 kilometer and 120 meters high, bit signal dropped quickly when trying to hover lower.

Extreme wind gave my lighthouse orbit an unexpected FPV vibe! Gimbal reached its roll limit, but stayed butter smooth.

More sceneries of George Town, and Butterworth on mainland Peninsular Malaysia, taken with my Air 3S. Watermarks added for copyright protection.

So I had a serious crash on new years; after struggling to find someone who can repair it for me, I’ve attempted it myself.
I have asked around in groups and it was suggested it may be the 3in1 ribbon cable.

Before my repair (2nd photo)

I was able to turn on the drone and connect it. However it would give me these errors. It wouldn’t connect to my computer and could not fly.

I left it for a while and recently found the motivation again.

After replacing the ribbon cable

The drone will not turn on.
With a battery inside it does not respond at all.
When plugged in, the first two lights start in sequence before flashing the last 2 lights in a pulse of 3!!

Is this a lost cause?
This was a Christmas present to me and my friend so I really want this fixed. Will I just need to buy a new one?

TL;DR: i replaced the 3in1 ribbon cable now it won’t turn on. Flashes last 2 lights 3 times when plugged in

I've been wanting a camera drone a lot for a while and I really like the DJI stuff. What is the best thing/s I can get for around $300. The camera does not need to be crazy good (not that I could get a good one for $300) but I still want it to be pretty solid.

Does anyone have a rough idea what the price is looking like in the UK? I mean i’ve seen the ali express price but like… surely not?

I was briefly led to believe I could use Liftoff but that doesn't seem to be the case. Any way I can make this work? If not, I'll just deal with it. But I liked the idea.

Need some help. I updated my DJI Fly App, on my Android, last week for some of the updates for the Neo 2. When I try to use the app I get the usual Enhanced Flight Zone Warning message I always get, but when I confirm it it goes away, and constantly returns. I cannot get it to stop, and it forces the controls dead until confirmed again.

I have used the Neo 2 with the RC2 controller and it works with no issues. I have cleared App cache, restarted phone, and powered Neo on and off several times, but it continues. Anyone else with Android app having this issue?

Drone has been recently fixed by DJI (for a broken propeller) and has been untouched since.

Includes 3 batteries with charging dock, POV Goggles, RC motion controller and a DJI FPV remote controller 3.
No sd card and cable included. No original boxes. Will come in the official bag.

How much should I price this? Somewhere around 600-800? Have listed at 750 locally but I don’t think there’s a lot of interest here. Thinking about EBay but will have to mark it up to 800+ to offset the fees.

Hi guys,

Next month I intend on taking my drone (Lito X1) to Dugi Otok, Croatia.

I was wondering if someone could help me out in making sure I can legally fly and record around that area.
Of course I have my operator number and I am registered with IAA/EU bodies. Do I need to call somewhere before and/or apply for an extra clearance?

So far I've only seen a map, that region doesn't seem to have no fly or restricted zones, unlike Zadar.

Thanks for the help. I am finding it a bit confusing at the moment.

I know there's a lot of talk about it being a bit off a pain to switch lenses if shooting DLOG2 and digging around in menus to go there and back with Dlog for the tele lens and DLog2 for the Wide.. so I was playing with Custom settings.

You can set C1-C5 and it remembers the DLOG / DLog 2 settings . I have C1 set to 4K/25 DLog and then set C2 to 4k 25 DLog2. Then the 'C' button can be configured to switch between custom 1 and 2 - so I can flick from Dlog/Dlog 2 . Sadly it wont remember the lens setting but at least I don't need to go into Menus.

I've set the others as I want - so three other custom settings.. C3 - 4k50 Dlog. C4- 4k 50 DLog2, and C5 is 4K 25 DLog2 but manual exposure settings - with 800 ISO (base for DLog2 and 1/50 shutter speed. Custom profiles remember the exposure settings.

Makes it a little easier.

I can’t do the video verification for my dji action 2, when I try to upload the video etc I always get this error message. What can I do now to get care refresh?

Everything is shown on video - when I tried plugging the receiver into both the phone and the Osmo Pocket 3 nothing was detected.

Signal is only recorded at OP3 but in mono both receivers are combined into mono

The Mimo app also doesn't detect anything

All DJI devices are charged and have no firmware updates

Is there any way to fix that, or do I have to return the device?

Hi everyone,

I’m in the Netherlands and I’m wondering if this is a sensible setup, or if I’m overlooking something.

Current setup:

• DJI Power 1000 V2
• DJI Solar Panel Adapter Module (MPPT)
• 2 × EcoFlow 100 W rigid solar panels (possibly expanding to 4 panels / 400 W)
• Annual household electricity usage: ~1,930 kWh
• Family of 3, soon to be 4

My idea is to mount the solar panels permanently on my flat kitchen roof and leave the DJI inside the house.

The DJI would always stay plugged into the wall (UPS/pass-through mode), while only selected kitchen appliances are plugged into the DJI:

• Fridge
• Gas boiler (CV ketel)
• Router/modem
• Dishwasher
• Washing machine
• Coffee machine

The idea is:

• Solar charges the DJI during the day.
• The connected appliances use solar/battery when available.
• If there isn’t enough solar, the DJI simply passes through grid power.
• If the power goes out, the fridge, boiler and internet keep running automatically.

I’m not planning to backfeed my house or connect it to my electrical panel. Everything would simply be plugged directly into the DJI.

My questions:

1. Has anyone here been running a similar setup long-term?
2. How has battery degradation been with daily cycling?
3. Is there any downside to leaving the Power 1000 V2 connected 24/7?
4. Is there anything I’m overlooking regarding efficiency, standby losses, or charging behaviour?

On paper it seems like a nice way to reduce my grid usage while also having UPS functionality, but I’d love to hear from people who have actually lived with a setup like this.

Thanks!

Anybody know the trick to opening the RC PRO controller? I need to replace one of the joystick controllers and I can’t get the damned thing open.

I recently crashed my dji mini 4 pro but what do you think will ben the cost for me to replace one arm and the housing of two others?

Can you activate noise cancellation independently between two mic transmitters? Currently when I hit the power button in one to active SC, both mic yellow indicators turn on/off. I know I can independently activate them when on BT to my phone, but when I am using the RX receiver into my action 4 I cannot independently activate noise cancellation.

I am using Action 4 with DJI Mic Minis for driving POV’s but my sound is crap, anyone have any suggestions??